how to take apart a glock magazine

kevenbetschman81387 May 01, 2022 apart , glock , magazine , wallpaper Comment

To get mine apart I have to put them in a small bench vise tighten them a bit push in the tab and then use a metal punch and rubber mallet to tap the plate past the two ears on the mag tube. Slide floorplate forward capturing spring with thumbs.

Pin On Glock S N More

Next wipe clean the base plate and spring plate.

. The tactical pasta strainer and the operator dishwasher are such key components of any cleaning regimen. Insert the follower and spring into the magazine tube as shown be sure the follower is oriented properly. This differs from what was taught in the book because according to Glock - the factory approved method of removing the baseplate will not work with the newer mags with the mags with the locking tabs.

What I tpically do is I take a shop rag wrap the mag and get some channel locks and get gently get the tabs to unlock with a slight amount of force. Watch the video above for a demonstration. Using your support hand to squeeze together the sides of the GTUL pull downward with the magazine brush to push the floor plate off the magazine tube.

Not only that it dented the hole in the floor plate and basically marred up the peg of the magazine plate. Remove the Barrel Next you need to pull the trigger then pull the slide back about a quarter of an inch. Next to the extractor you will find the firing-pin safety lock it resembles a small round button.

Unload Your Glock First make sure the gun is unloaded before you disassemble it. Then you need to check the chamber and make sure to remove any ammunition present. Glock Magazine Disassembly And Reassembly Youtube This GLOCK 17 Gen4 gas blowback airsoft gun from Umarex boasts an enhanced grip texture.

While firmly holding the magazine in your support hand take the magazine brush and use the punch on its base to fully depress the magazines retaining button on the bottom of the floor plate. Step 5 - Remove the Extractor and Safety Plunger. Now that your firing pin assembly and plunger are out draw your attention to the outside of the slide.

Small freaking problem though. Takes a little force but always works and the mag reassembles fine. To prevent injury gradually release tension until spring is removed keeping magazine pointed in a safe direction.

The tool cracked the magazine insert in half. You want to leverage the. Ive disassembled Glock mags a bazillion times by simply inserting the armorers tool into the hole in the basepad all the way to the plastic handle of the tool and then prying the base pad off of the magazine body.

Added tip if you run across one that the ears that hold the base plate on are slightly larger you can take a squeeze clamp and just compress the sides of the magazine body ever so slightly near the base and they will slide off. You dont need to squeeze the sides of the mag as much as you might think. 044 Ahhahahhaha Wear this shirt in your videos with 5 paper-clipped to it.

Holding GTUL with logo facing up insert magazine. This tool is designed to ease the removal the floorplate on your double stack Glock magazines while preventing wear on the locking tabs and damage to the metal magazine lining. I took the stick your Glock tool in the hole and depress the sides of the magazine and gently tug it off approach.

Order Online or Call Toll-Free. Squeeze GTUL and pull forward with punch to expose magazine spring as shown. I show how to take apart the Glock magazine and put it back together.

Second work the slide a couple of times to be sure the chamber is clear. Im sure there are several different ways to take apart the magazine. Use the oil- dampened cloth to wipe down the length of the magazine spring and also wipe down the follower.

Luckily I was shown a way that makes disassembling a Glock magazine very simple. Push the tool with the baseplate sliding forward. Insert the tool all the way in until it stops at the handle.

Now you are ready to reassemble your Glock magazine. Fourth pointing the gun in a safe direction pull the trigger. These are Glock factory latest generation handgun magazines.

First Remove the magazine. Everybody needs magazines. I have seen some bat-shit crazy explanations of how to disassemble a Glock magazine well here is the proper way to do it.

Press it in using your Glock Tool and you can now remove the extractor as well as the pin. You can just brute force the plate off without causing any permanent damage. Third check AGAIN to be sure the chamber is clear.

Think I originally saw this method in a YouTube clip. If the magazine is longe. Use the Glock Armorers Tool.

Heres how to take a Glock apart for cleaning. Arguably the most well recognized name in pistols the Glock 17 is known the world over. The 10-rd mags have molded-in ribs on the interior essentially creating a single-stack magazine resulting in a much stiffer mag.

How to Disassemble a Glock Instructions. If Matt lived in California the Pusha-T line Look in the Frigidaire 25 to life in here would. I use a Glock armorers tool and stick it in the bottom of the mag and then press the tip of the tool against the inside wall and use it as a lever to slide the plate off.

100 Shell just about disassemble herself. Each are drop free metal lined brand new. Push retaining pin into magazine tube with punch.

If you need help or have question.

Glock 43 With And Without 2 Extended Magazine Base Guns Guns Pistols Glock 43